Comments on: uhso(4): Option HSDPA driver for FreeBSD 8 http://www.shapeshifter.se/2009/07/20/uhso4-option-hsdpa-driver-for-freebsd-8/ Mostly miscellaneous technical mumbo-jumbo. Fri, 10 Feb 2012 04:51:21 +0100 http://wordpress.org/?v=2.8.6 hourly 1 By: e0je http://www.shapeshifter.se/2009/07/20/uhso4-option-hsdpa-driver-for-freebsd-8/comment-page-1/#comment-2950 e0je Sat, 11 Sep 2010 07:58:15 +0000 http://www.shapeshifter.se/?p=633#comment-2950 Fredrik, I bought an option 225 but my system still locks up and leaves me to have to reboot. Is there some sort of conflicts in my kernel that I need to remove? I want my USB modem to be recognized under freebsd so i can use the smstools3 port as a sms gateway.... It locks up when every i try to send data to the device. Fredrik,

I bought an option 225 but my system still locks up and leaves me to have to reboot. Is there some sort of conflicts in my kernel that I need to remove?

I want my USB modem to be recognized under freebsd so i can use the smstools3 port as a sms gateway….

It locks up when every i try to send data to the device.

]]> By: e0je http://www.shapeshifter.se/2009/07/20/uhso4-option-hsdpa-driver-for-freebsd-8/comment-page-1/#comment-2941 e0je Sun, 05 Sep 2010 01:48:46 +0000 http://www.shapeshifter.se/?p=633#comment-2941 ugen4.1: at usbus4, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON bLength = 0x0012 bDescriptorType = 0x0001 bcdUSB = 0x0200 bDeviceClass = 0x0009 bDeviceSubClass = 0x0000 bDeviceProtocol = 0x0001 bMaxPacketSize0 = 0x0040 idVendor = 0x0000 idProduct = 0x0000 bcdDevice = 0x0100 iManufacturer = 0x0001 iProduct = 0x0002 iSerialNumber = 0x0000 bNumConfigurations = 0x0001 usbconfig -u 4 -a 1 dump_all_config_desc ugen4.1: at usbus4, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON Configuration index 0 bLength = 0x0009 bDescriptorType = 0x0002 wTotalLength = 0x0019 bNumInterfaces = 0x0001 bConfigurationValue = 0x0001 iConfiguration = 0x0000 bmAttributes = 0x0040 bMaxPower = 0x0000 Interface 0 bLength = 0x0009 bDescriptorType = 0x0004 bInterfaceNumber = 0x0000 bAlternateSetting = 0x0000 bNumEndpoints = 0x0001 bInterfaceClass = 0x0009 bInterfaceSubClass = 0x0000 bInterfaceProtocol = 0x0000 iInterface = 0x0000 Endpoint 0 bLength = 0x0007 bDescriptorType = 0x0005 bEndpointAddress = 0x0081 bmAttributes = 0x0003 wMaxPacketSize = 0x0008 bInterval = 0x00ff bRefresh = 0x0000 bSynchAddress = 0x0000 ------ anyone have any luck getting this to work with smstools3 ? when i try to sendsms to /dev/cuaU3 my system locks up and I have to reboot. ugen4.1: at usbus4, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON

bLength = 0×0012
bDescriptorType = 0×0001
bcdUSB = 0×0200
bDeviceClass = 0×0009
bDeviceSubClass = 0×0000
bDeviceProtocol = 0×0001
bMaxPacketSize0 = 0×0040
idVendor = 0×0000
idProduct = 0×0000
bcdDevice = 0×0100
iManufacturer = 0×0001
iProduct = 0×0002
iSerialNumber = 0×0000
bNumConfigurations = 0×0001

usbconfig -u 4 -a 1 dump_all_config_desc
ugen4.1: at usbus4, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON

Configuration index 0

bLength = 0×0009
bDescriptorType = 0×0002
wTotalLength = 0×0019
bNumInterfaces = 0×0001
bConfigurationValue = 0×0001
iConfiguration = 0×0000
bmAttributes = 0×0040
bMaxPower = 0×0000

Interface 0
bLength = 0×0009
bDescriptorType = 0×0004
bInterfaceNumber = 0×0000
bAlternateSetting = 0×0000
bNumEndpoints = 0×0001
bInterfaceClass = 0×0009
bInterfaceSubClass = 0×0000
bInterfaceProtocol = 0×0000
iInterface = 0×0000

Endpoint 0
bLength = 0×0007
bDescriptorType = 0×0005
bEndpointAddress = 0×0081
bmAttributes = 0×0003
wMaxPacketSize = 0×0008
bInterval = 0×00ff
bRefresh = 0×0000
bSynchAddress = 0×0000
——

anyone have any luck getting this to work with smstools3 ? when i try to sendsms to /dev/cuaU3 my system locks up and I have to reboot.

]]> By: e0je http://www.shapeshifter.se/2009/07/20/uhso4-option-hsdpa-driver-for-freebsd-8/comment-page-1/#comment-2940 e0je Sun, 05 Sep 2010 01:04:18 +0000 http://www.shapeshifter.se/?p=633#comment-2940 Resolved... I had a bad USB controller, replaced with a new PCI Controller and card is detected :) thanks Fredrik Resolved… I had a bad USB controller, replaced with a new PCI Controller and card is detected :) thanks Fredrik

]]> By: e0je http://www.shapeshifter.se/2009/07/20/uhso4-option-hsdpa-driver-for-freebsd-8/comment-page-1/#comment-2937 e0je Sat, 04 Sep 2010 07:55:19 +0000 http://www.shapeshifter.se/?p=633#comment-2937 any ideas? any ideas?

]]> By: e0je http://www.shapeshifter.se/2009/07/20/uhso4-option-hsdpa-driver-for-freebsd-8/comment-page-1/#comment-2934 e0je Tue, 31 Aug 2010 05:48:56 +0000 http://www.shapeshifter.se/?p=633#comment-2934 btw i'm using module from ports uhso-20100416 and uname -a is FreeBSD bsd.sprintbusiness.net 8.1-STABLE FreeBSD 8.1-STABLE #1: Sat Aug 21 15:40:01 PDT 2010 xxxx@bsd.xxxxxx:/usr/obj/usr/src/sys/GENERIC amd64 btw i’m using module from ports uhso-20100416 and uname -a is FreeBSD bsd.sprintbusiness.net 8.1-STABLE FreeBSD 8.1-STABLE #1: Sat Aug 21 15:40:01 PDT 2010 xxxx@bsd.xxxxxx:/usr/obj/usr/src/sys/GENERIC amd64

]]> By: e0je http://www.shapeshifter.se/2009/07/20/uhso4-option-hsdpa-driver-for-freebsd-8/comment-page-1/#comment-2933 e0je Tue, 31 Aug 2010 05:47:17 +0000 http://www.shapeshifter.se/?p=633#comment-2933 I have an option icon 322 and dmesg gives the following output when its inserted, usb_alloc_device: set address 2 failed (USB_ERR_IOERROR, ignored) usb_alloc_device: getting device descriptor at addr 2 failed, USB_ERR_IOERROR usbd_req_re_enumerate: addr=2, set address failed! (USB_ERR_IOERROR, ignored) usbd_req_re_enumerate: getting device descriptor at addr 2 failed, USB_ERR_IOERROR usbd_req_re_enumerate: addr=2, set address failed! (USB_ERR_IOERROR, ignored) usbd_req_re_enumerate: getting device descriptor at addr 2 failed, USB_ERR_IOERROR ugen0.2: at usbus0 (disconnected) uhub_reattach_port: could not allocate new device Any ideas how i can get this to work? thanks I have an option icon 322 and dmesg gives the following output when its inserted,

usb_alloc_device: set address 2 failed (USB_ERR_IOERROR, ignored)
usb_alloc_device: getting device descriptor at addr 2 failed, USB_ERR_IOERROR
usbd_req_re_enumerate: addr=2, set address failed! (USB_ERR_IOERROR, ignored)
usbd_req_re_enumerate: getting device descriptor at addr 2 failed, USB_ERR_IOERROR
usbd_req_re_enumerate: addr=2, set address failed! (USB_ERR_IOERROR, ignored)
usbd_req_re_enumerate: getting device descriptor at addr 2 failed, USB_ERR_IOERROR
ugen0.2: at usbus0 (disconnected)
uhub_reattach_port: could not allocate new device

Any ideas how i can get this to work? thanks

]]> By: mariusz http://www.shapeshifter.se/2009/07/20/uhso4-option-hsdpa-driver-for-freebsd-8/comment-page-1/#comment-2859 mariusz Tue, 08 Jun 2010 22:36:22 +0000 http://www.shapeshifter.se/?p=633#comment-2859 and tthis lap# sysctl dev.uhso dev.uhso.0.%desc: Network dev.uhso.0.%driver: uhso dev.uhso.0.%location: port=1 interface=0 dev.uhso.0.%pnpinfo: vendor=0x0af0 product=0xc031 devclass=0xff devsubclass=0xff sernum="serial_number" release=0x0100 intclass=0xff intsubclass=0xff dev.uhso.0.%parent: uhub0 dev.uhso.0.netif: uhso0 dev.uhso.0.type: Network/Serial dev.uhso.0.ports: 2 dev.uhso.0.port.control.tty: cuaU0.0 dev.uhso.0.port.control.desc: Control dev.uhso.0.port.application.tty: cuaU0.1 dev.uhso.0.port.application.desc: Application dev.uhso.1.%desc: Diagnostic dev.uhso.1.%driver: uhso dev.uhso.1.%location: port=1 interface=1 dev.uhso.1.%pnpinfo: vendor=0x0af0 product=0xc031 devclass=0xff devsubclass=0xff sernum="serial_number" release=0x0100 intclass=0xff intsubclass=0xff dev.uhso.1.%parent: uhub0 dev.uhso.1.type: Serial dev.uhso.1.ports: 1 dev.uhso.1.port.diagnostic.tty: cuaU2 dev.uhso.1.port.diagnostic.desc: Diagnostic dev.uhso.2.%desc: Modem dev.uhso.2.%driver: uhso dev.uhso.2.%location: port=1 interface=2 dev.uhso.2.%pnpinfo: vendor=0x0af0 product=0xc031 devclass=0xff devsubclass=0xff sernum="serial_number" release=0x0100 intclass=0xff intsubclass=0xff dev.uhso.2.%parent: uhub0 dev.uhso.2.type: Serial dev.uhso.2.ports: 1 dev.uhso.2.port.modem.tty: cuaU3 dev.uhso.2.port.modem.desc: Modem and tthis

lap# sysctl dev.uhso
dev.uhso.0.%desc: Network
dev.uhso.0.%driver: uhso
dev.uhso.0.%location: port=1 interface=0
dev.uhso.0.%pnpinfo: vendor=0×0af0 product=0xc031 devclass=0xff devsubclass=0xff sernum=”serial_number” release=0×0100 intclass=0xff intsubclass=0xff
dev.uhso.0.%parent: uhub0
dev.uhso.0.netif: uhso0
dev.uhso.0.type: Network/Serial
dev.uhso.0.ports: 2
dev.uhso.0.port.control.tty: cuaU0.0
dev.uhso.0.port.control.desc: Control
dev.uhso.0.port.application.tty: cuaU0.1
dev.uhso.0.port.application.desc: Application
dev.uhso.1.%desc: Diagnostic
dev.uhso.1.%driver: uhso
dev.uhso.1.%location: port=1 interface=1
dev.uhso.1.%pnpinfo: vendor=0×0af0 product=0xc031 devclass=0xff devsubclass=0xff sernum=”serial_number” release=0×0100 intclass=0xff intsubclass=0xff
dev.uhso.1.%parent: uhub0
dev.uhso.1.type: Serial
dev.uhso.1.ports: 1
dev.uhso.1.port.diagnostic.tty: cuaU2
dev.uhso.1.port.diagnostic.desc: Diagnostic
dev.uhso.2.%desc: Modem
dev.uhso.2.%driver: uhso
dev.uhso.2.%location: port=1 interface=2
dev.uhso.2.%pnpinfo: vendor=0×0af0 product=0xc031 devclass=0xff devsubclass=0xff sernum=”serial_number” release=0×0100 intclass=0xff intsubclass=0xff
dev.uhso.2.%parent: uhub0
dev.uhso.2.type: Serial
dev.uhso.2.ports: 1
dev.uhso.2.port.modem.tty: cuaU3
dev.uhso.2.port.modem.desc: Modem

]]> By: mariusz http://www.shapeshifter.se/2009/07/20/uhso4-option-hsdpa-driver-for-freebsd-8/comment-page-1/#comment-2858 mariusz Tue, 08 Jun 2010 22:30:17 +0000 http://www.shapeshifter.se/?p=633#comment-2858 Helo, A have a problem with Option ICON 031, Modem don't work , I’m using FreeBSD 8.0-RELEASE. I still can not connect to the internet Please, help me! lap# usbconfig -u 0 -a 2 dump_device_desc ugen0.2: at usbus0, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON bLength = 0x0012 bDescriptorType = 0x0001 bcdUSB = 0x0110 bDeviceClass = 0x0000 bDeviceSubClass = 0x0000 bDeviceProtocol = 0x0000 bMaxPacketSize0 = 0x0040 idVendor = 0x0af0 idProduct = 0xc031 bcdDevice = 0x0100 iManufacturer = 0x0001 iProduct = 0x0002 iSerialNumber = 0x0003 bNumConfigurations = 0x0001 lap# usbconfig -u 0 -a 2 dump_all_config_desc ugen0.2: at usbus0, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON Configuration index 0 bLength = 0x0009 bDescriptorType = 0x0002 wTotalLength = 0x0020 bNumInterfaces = 0x0001 bConfigurationValue = 0x0001 iConfiguration = 0x0004 bmAttributes = 0x00c0 bMaxPower = 0x0032 Interface 0 bLength = 0x0009 bDescriptorType = 0x0004 bInterfaceNumber = 0x0000 bAlternateSetting = 0x0000 bNumEndpoints = 0x0002 bInterfaceClass = 0x0008 bInterfaceSubClass = 0x0006 bInterfaceProtocol = 0x0050 iInterface = 0x0005 Endpoint 0 bLength = 0x0007 bDescriptorType = 0x0005 bEndpointAddress = 0x0081 bmAttributes = 0x0002 wMaxPacketSize = 0x0040 bInterval = 0x0000 bRefresh = 0x0000 bSynchAddress = 0x0000 Endpoint 1 bLength = 0x0007 bDescriptorType = 0x0005 bEndpointAddress = 0x0002 bmAttributes = 0x0002 wMaxPacketSize = 0x0040 bInterval = 0x0000 bRefresh = 0x0000 bSynchAddress = 0x0000 Thanks, MAriusz Helo,
A have a problem with Option ICON 031,
Modem don’t work ,
I’m using FreeBSD 8.0-RELEASE. I still can not connect to the internet
Please, help me!

lap# usbconfig -u 0 -a 2 dump_device_desc
ugen0.2: at usbus0, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON

bLength = 0×0012
bDescriptorType = 0×0001
bcdUSB = 0×0110
bDeviceClass = 0×0000
bDeviceSubClass = 0×0000
bDeviceProtocol = 0×0000
bMaxPacketSize0 = 0×0040
idVendor = 0×0af0
idProduct = 0xc031
bcdDevice = 0×0100
iManufacturer = 0×0001
iProduct = 0×0002
iSerialNumber = 0×0003
bNumConfigurations = 0×0001

lap# usbconfig -u 0 -a 2 dump_all_config_desc
ugen0.2: at usbus0, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON

Configuration index 0

bLength = 0×0009
bDescriptorType = 0×0002
wTotalLength = 0×0020
bNumInterfaces = 0×0001
bConfigurationValue = 0×0001
iConfiguration = 0×0004
bmAttributes = 0×00c0
bMaxPower = 0×0032

Interface 0
bLength = 0×0009
bDescriptorType = 0×0004
bInterfaceNumber = 0×0000
bAlternateSetting = 0×0000
bNumEndpoints = 0×0002
bInterfaceClass = 0×0008
bInterfaceSubClass = 0×0006
bInterfaceProtocol = 0×0050
iInterface = 0×0005

Endpoint 0
bLength = 0×0007
bDescriptorType = 0×0005
bEndpointAddress = 0×0081
bmAttributes = 0×0002
wMaxPacketSize = 0×0040
bInterval = 0×0000
bRefresh = 0×0000
bSynchAddress = 0×0000

Endpoint 1
bLength = 0×0007
bDescriptorType = 0×0005
bEndpointAddress = 0×0002
bmAttributes = 0×0002
wMaxPacketSize = 0×0040
bInterval = 0×0000
bRefresh = 0×0000
bSynchAddress = 0×0000

Thanks,
MAriusz

]]> By: haripour http://www.shapeshifter.se/2009/07/20/uhso4-option-hsdpa-driver-for-freebsd-8/comment-page-1/#comment-2751 haripour Thu, 18 Feb 2010 06:47:58 +0000 http://www.shapeshifter.se/?p=633#comment-2751 I'm so sorry. I used copy/paste that's not work. The trully output is, #usbconfig ..... ugen2.4: at usbus2, cfg=0 md=HOST spd-HIGH (480Mbps) pwr=ON #usconfig -u 2 -a 4 dump_device_desc ugen2.4: at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON bLength = 0x0012 bDescriptorType = 0x0001 ..... Thanks, Hari I’m so sorry. I used copy/paste that’s not work. The trully output is,

#usbconfig
…..
ugen2.4: at usbus2, cfg=0 md=HOST spd-HIGH (480Mbps) pwr=ON

#usconfig -u 2 -a 4 dump_device_desc
ugen2.4: at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON

bLength = 0×0012
bDescriptorType = 0×0001
…..

Thanks,
Hari

]]> By: haripour http://www.shapeshifter.se/2009/07/20/uhso4-option-hsdpa-driver-for-freebsd-8/comment-page-1/#comment-2750 haripour Thu, 18 Feb 2010 06:34:03 +0000 http://www.shapeshifter.se/?p=633#comment-2750 I'm a newuser in FreeBSD. I'm using FreeBSD 8.0-RELEASE. I still can not connect to the internet. Below is the output of usbconfig command. How can I solved this problem? #usbconfig ugen0.1: at usbus0, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON ugen1.1: at usbus1, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON ugen2.1: at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON ugen2.2: at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON ugen2.3: at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON ugen1.2: at usbus1, cfg=0 md=HOST spd=LOW (1.5Mbps) pwr=ON ugen2.4: at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON #usbconfig -u 2 -a 4 dump_device_desc ugen2.4: at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON bLength = 0x0012 bDescriptorType = 0x0001 bcdUSB = 0x0200 bDeviceClass = 0x00ff bDeviceSubClass = 0x00ff bDeviceProtocol = 0x00ff bMaxPacketSize0 = 0x0040 idVendor = 0x0af0 idProduct = 0x7501 bcdDevice = 0x0000 iManufacturer = 0x0002 iProduct = 0x0001 iSerialNumber = 0x0000 bNumConfigurations = 0x0001 #usbconfig -u 2 -a 4 dump_all_config_desc ugen2.4: at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON Configuration index 0 bLength = 0x0009 bDescriptorType = 0x0002 wTotalLength = 0x0020 bNumInterfaces = 0x0001 bConfigurationValue = 0x0001 iConfiguration = 0x0000 bmAttributes = 0x0080 bMaxPower = 0x00fa Interface 0 bLength = 0x0009 bDescriptorType = 0x0004 bInterfaceNumber = 0x0000 bAlternateSetting = 0x0000 bNumEndpoints = 0x0002 bInterfaceClass = 0x0008 bInterfaceSubClass = 0x0006 bInterfaceProtocol = 0x0050 iInterface = 0x0000 Endpoint 0 bLength = 0x0007 bDescriptorType = 0x0005 bEndpointAddress = 0x0001 bmAttributes = 0x0002 wMaxPacketSize = 0x0200 bInterval = 0x0000 bRefresh = 0x0000 bSynchAddress = 0x0000 Endpoint 1 bLength = 0x0007 bDescriptorType = 0x0005 bEndpointAddress = 0x0081 bmAttributes = 0x0002 wMaxPacketSize = 0x0200 bInterval = 0x0000 bRefresh = 0x0000 bSynchAddress = 0x0000 Thankyou very much, Regards, Hari I’m a newuser in FreeBSD. I’m using FreeBSD 8.0-RELEASE. I still can not connect to the internet. Below is the output of usbconfig command. How can I solved this problem?

#usbconfig
ugen0.1: at usbus0, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON
ugen1.1: at usbus1, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON
ugen2.1: at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON
ugen2.2: at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON
ugen2.3: at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON
ugen1.2: at usbus1, cfg=0 md=HOST spd=LOW (1.5Mbps) pwr=ON
ugen2.4: at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON

#usbconfig -u 2 -a 4 dump_device_desc
ugen2.4: at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON

bLength = 0×0012
bDescriptorType = 0×0001
bcdUSB = 0×0200
bDeviceClass = 0×00ff
bDeviceSubClass = 0×00ff
bDeviceProtocol = 0×00ff
bMaxPacketSize0 = 0×0040
idVendor = 0×0af0
idProduct = 0×7501
bcdDevice = 0×0000
iManufacturer = 0×0002
iProduct = 0×0001
iSerialNumber = 0×0000
bNumConfigurations = 0×0001

#usbconfig -u 2 -a 4 dump_all_config_desc
ugen2.4: at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON

Configuration index 0

bLength = 0×0009
bDescriptorType = 0×0002
wTotalLength = 0×0020
bNumInterfaces = 0×0001
bConfigurationValue = 0×0001
iConfiguration = 0×0000
bmAttributes = 0×0080
bMaxPower = 0×00fa

Interface 0
bLength = 0×0009
bDescriptorType = 0×0004
bInterfaceNumber = 0×0000
bAlternateSetting = 0×0000
bNumEndpoints = 0×0002
bInterfaceClass = 0×0008
bInterfaceSubClass = 0×0006
bInterfaceProtocol = 0×0050
iInterface = 0×0000

Endpoint 0
bLength = 0×0007
bDescriptorType = 0×0005
bEndpointAddress = 0×0001
bmAttributes = 0×0002
wMaxPacketSize = 0×0200
bInterval = 0×0000
bRefresh = 0×0000
bSynchAddress = 0×0000

Endpoint 1
bLength = 0×0007
bDescriptorType = 0×0005
bEndpointAddress = 0×0081
bmAttributes = 0×0002
wMaxPacketSize = 0×0200
bInterval = 0×0000
bRefresh = 0×0000
bSynchAddress = 0×0000

Thankyou very much,

Regards,
Hari

]]>